[ 0.000000] Linux version 3.2.9 (openwrt@OpenWRTBuild) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Tue Mar 13 20:33:19 MST 2012
[ 0.000000] MyLoader: sysp=00d73bc7, boardp=ed0c292e, parts=97cba183
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9330 rev 1
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 802e4c80, node_mem_map 81000000
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8128 pages, LIFO batch:0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=TL-WR703N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 29180k/32768k available (2171k kernel code, 3588k reserved, 409k data, 196k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:48
[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] MIPS: machine is TP-LINK TL-WR703N v1
[ 0.330000] bio: create slab <bio-0> at 0
[ 0.340000] Switching to clocksource MIPS
[ 0.350000] NET: Registered protocol family 2
[ 0.350000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.350000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.360000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.360000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.370000] TCP reno registered
[ 0.370000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.380000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.380000] NET: Registered protocol family 1
[ 0.390000] PCI: CLS 0 bytes, default 32
[ 0.410000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.410000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.420000] msgmni has been set to 56
[ 0.430000] io scheduler noop registered
[ 0.430000] io scheduler deadline registered (default)
[ 0.430000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.440000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[ 0.450000] console [ttyATH0] enabled, bootconsole disabled
[ 0.460000] m25p80 spi0.0: found s25sl032a, expected m25p80
[ 0.470000] m25p80 spi0.0: s25sl032a (4096 Kbytes)
[ 0.470000] 5 tp-link partitions found on MTD device spi0.0
[ 0.480000] Creating 5 MTD partitions on "spi0.0":
[ 0.480000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.490000] 0x000000020000-0x0000001049a0 : "kernel"
[ 0.490000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.500000] 0x0000001049a0-0x0000003f0000 : "rootfs"
[ 0.510000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.520000] mtd: partition "rootfs" set to be root filesystem
[ 0.530000] mtd: partition "rootfs_data" created automatically, ofs=270000, len=180000
[ 0.530000] 0x000000270000-0x0000003f0000 : "rootfs_data"
[ 0.540000] 0x0000003f0000-0x000000400000 : "art"
[ 0.550000] 0x000000020000-0x0000003f0000 : "firmware"
[ 0.800000] ag71xx_mdio: probed
[ 0.800000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 1.410000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[ 1.410000] TCP westwood registered
[ 1.420000] NET: Registered protocol family 17
[ 1.420000] Bridge firewalling registered
[ 1.420000] 8021q: 802.1Q VLAN Support v1.8
[ 1.450000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.450000] Freeing unused kernel memory: 196k freed
[ 5.380000] Registered led device: tp-link:blue:system
[ 8.990000] JFFS2 notice: (403) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 11 of xref (0 dead, 4 orphan) found.
[ 11.300000] Compat-wireless backport release: compat-wireless-2012-02-27-1-r30919
[ 11.300000] Backport based on wireless-testing.git master-2012-02-27
[ 11.340000] cfg80211: Calling CRDA to update world regulatory domain
[ 11.640000] usbcore: registered new interface driver usbfs
[ 11.640000] usbcore: registered new interface driver hub
[ 11.650000] usbcore: registered new device driver usb
[ 12.160000] cfg80211: World regulatory domain updated:
[ 12.170000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 12.170000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.180000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 12.190000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 12.200000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.200000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.760000] ath: EEPROM regdomain: 0x0
[ 12.760000] ath: EEPROM indicates default country code should be used
[ 12.760000] ath: doing EEPROM country->regdmn map search
[ 12.760000] ath: country maps to regdmn code: 0x3a
[ 12.760000] ath: Country alpha2 being used: US
[ 12.760000] ath: Regpair used: 0x3a
[ 12.770000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 12.770000] Registered led device: ath9k-phy0
[ 12.770000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[ 12.780000] cfg80211: Calling CRDA for country: US
[ 12.950000] cfg80211: Regulatory domain changed to country: US
[ 12.960000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 12.960000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 12.970000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 12.980000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.990000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.990000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.000000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 13.010000] PPP generic driver version 2.4.2
[ 13.160000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 13.280000] NET: Registered protocol family 24
[ 13.420000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 13.420000] ath79-ehci ar933x-ehci: Atheros built-in EHCI controller
[ 13.430000] ath79-ehci ar933x-ehci: new USB bus registered, assigned bus number 1
[ 13.470000] ath79-ehci ar933x-ehci: irq 3, io mem 0x1b000000
[ 13.490000] ath79-ehci ar933x-ehci: USB 2.0 started, EHCI 1.00
[ 13.490000] hub 1-0:1.0: USB hub found
[ 13.490000] hub 1-0:1.0: 1 port detected
[ 13.520000] nf_conntrack version 0.5.0 (459 buckets, 1836 max)
[ 13.750000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 13.810000] uhci_hcd: USB Universal Host Controller Interface driver
[ 13.820000] usb 1-1: new high-speed USB device number 2 using ath79-ehci
[ 14.010000] usbcore: registered new interface driver usbserial
[ 14.020000] USB Serial support registered for generic
[ 14.030000] usbcore: registered new interface driver usbserial_generic
[ 14.040000] usbserial: USB Serial Driver core
[ 14.110000] USB Serial support registered for GSM modem (1-port)
[ 14.120000] option 1-1:1.0: GSM modem (1-port) converter detected
[ 14.120000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 14.130000] option 1-1:1.1: GSM modem (1-port) converter detected
[ 14.130000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 14.140000] option 1-1:1.2: GSM modem (1-port) converter detected
[ 14.150000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
[ 14.150000] usbcore: registered new interface driver option
[ 14.160000] option: v0.7.2:USB Driver for GSM modems
[ 17.100000] device wlan0 entered promiscuous mode
[ 19.600000] device wlan0 left promiscuous mode
[ 19.600000] br-lan: port 1(wlan0) entering disabled state
[ 19.880000] device eth0 entered promiscuous mode
[ 19.980000] device wlan0 entered promiscuous mode
[ 22.090000] br-lan: port 2(wlan0) entering forwarding state
[ 22.100000] br-lan: port 2(wlan0) entering forwarding state
[ 37.120000] br-lan: port 2(wlan0) entering forwarding state
А вебкамеру не прикрутил? 
backup-OpenWrt-2012-04-06.tar.gz
